Controlled-products-systems-group 2000E Manual de usuario descargar pdf

2000 Series

e/eM Style Keypad

Installation and Programming Guide

Models 2000e and 2000eM

Specifications

Parameter Specifications

Voltage Requirements 10-30 VDC; 12-24VAC

Keypad Current

Requirements (Max)

VDC VAC

10V: 85mA

30V: 115mA

12V: 150mA

24V: 200mA

Keypad with Output

Expansion Module (2000-

8EX) Current Requirements

(Max)

VDC VAC

10V: 230mA

30V: 390mA

12V: 500mA

24V: 700mA

Note: This is total maximum current

including keypad and output module.

Relay Contact Rating 2A @ 30VDC (Main & Aux)

REX Input Normally Open Dry Contact

Door Position Switch Input Normally Closed Dry Contact

Mechanical Dimensions 4.50" H x 2.75" W x 0.60" D

Environment Indoor or Outdoor

Temperature Tolerance -31°F to 151°F (-35ºC to 66°C)

Front End Cable Type Stranded and Shielded

Front End Distance and Wire

Gauge

1000 Ft. – 18AWG; 500 Ft – 20 AWG;

250 Ft. – 22 AWG

Firmware Version

1.0x (“1” is the major version; “0” is

the minor version; “x” is a minor

version, reserved for bug fixes, which

is indicated with a letter, such as “a”.)

Technical Support

Service Company: To contact IEI’s Technical Support

department, call 1- 800-343-9502, Monday through Friday.

Questions can also be submitted through our website at

www.ieib.com

End User: Please contact your service company.

Keypad Operating Modes

The 2000e/2000eM keypad has three operating modes: Standalone

Mode, Secured Series Front End Mode and Wiegand Front End

Mode. Below is a brief explanation of each mode. Refer to the

programming section for details about selecting each mode.

Standalone Mode:

By default, the keypad is programmed for Standalone Mode. In

this mode, all the users and other programming options are

maintained within the keypad and no additional controller is

required. The lock and all other inputs and outputs are connected

directly to the keypad.

Secured Series Front End Mode:

In Secured Series Front End mode, an IEI Secured Series

Controller is required. The IEI Secured Series Controller

maintains the users and programming options and makes all the

access control decisions. The locking device and all inputs and

outputs are connected to the controller. The 2000e/eM keypads

were evaluated by UL, in Secured Series Front End mode, for

use only with the IEI Hub Max II and Hub MiniMax II products.

Wiegand Front End Mode:

In Wiegand Front End mode, a separate Wiegand Access Control

panel is required. When you enter a code on the keypad it is then

sent to the control panel as Wiegand card data, depending on

which format you've programmed it for. The control panel

maintains the users and programming options and makes all the

access control decisions. The locking device and all inputs and

outputs are connected to the control panel. The 2000e/eM

keypads were evaluated by UL, in Wiegand Front End mode, for

use only with the IEI Hub Max II and Hub MiniMax II products

used in conjunction with the Wiegand Interface Module.

Mounting the Keypad

The keypad is designed to be flush mounted using a standard UL

Listed single-gang electrical box. Mounting height can vary

depending on requirements. An appropriate range is typically

between 48 and 52 inches on center off the floor.

For outdoor installations, use a UL Listed weatherproof back box

and seal the wire entry locations with silicone and provide a drain

hole. For additional protection, install the provided foam gasket

between the keypad and the back box. In addition, use the anti-

oxidant grease pack for the wire harness connectors.

Document #: 6104402, Rev 2.0 Page 1 of 8

Note: For additional information about installing and

programming the 2000e/2000eM keypad please contact

IEI at 1- 800-343-9502

1 2 3 4 5 6 7 8

Indice de contenidos

Pagina 1 - 2000 Series

2000 Series e/eM Style Keypad Installation and Programming GuideModels 2000e and 2000eMSpecificationsParameter SpecificationsVoltage Requirements 10-3

Pagina 2 - UL Requirements

Circuit Board DiagramMain Wire Harness (P2)Pin Wire Color Description1 Red V+ (Keypad Power)2 Black V- (Keypad Power)3 White/Black Wiegand Data 0/Secu

Pagina 3

Wiring a Maglock (Fail-Safe)1. Connect the red wire (V+) to the blue wire (common), andthen connect them to the positive on the power supply.2. Connec

Pagina 4

Changing the Master CodeThe first step in setting up your keypad is to enter program modeand change the master code. The default master code is 1234.1

Pagina 5 - Programming Keypad Options

Assigning Virtual Outputs to PhysicalOutputs(Standalone Mode Only)The keypad is equipped with nineteen Virtual Outputs and twelvePhysical Outputs. Vir

Pagina 6 - Resetting the Keypad

Programming Keypad Parameters(Default settings are in bold)Command/Action Keys to Enter/DetailsChange Keypad Parameters 32 # parameter # value # **Par

Pagina 7 - Loopback

Wiring the 2000-8EX Output ModuleIf the Output Module is within 18 inches of the keypad, use the 6-conductor wire harness, supplied with the Output Mo

Pagina 8

Document #: 6104402, Rev 2.0

Comentarios a estos manuales

Sin comentarios

Controlled-products-systems-group 2000E Manual de usuario

Busca en linea o descarga Manual de usuario para Panel De Control Controlled-products-systems-group 2000E. Controlled Products Systems Group 2000E User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Panel De Control Controlled-products-systems-group 2000E