Controlled-products-systems-group 8550C-7 Manual de usuario descargar pdf (Pagina 30)

USING THE DOOR CONTROL

SYNCHRONIZETHEDOORCONTROL

To synchronize the door control to the garage door opener,press the push bar until the garage door

opener activates(it may take up to 3 presses). Testthe door control by pressing the push bar, each

press ofthe push bar will activate the garage door opener.

Push Bar

LIGHT

button

reen

Motion

nsor

Navigation

Buttons

PUSH BAR

Press the push bar to open or close the door.

NAVIGATION BUTTONS

Use the navigation buttons to make selections and program features.

LIGHT BUTTON

Press the LIGHTbutton to turn the garage door opener lights on or off. When the lights are turned on

they will stay on until the LIGHT button is pressed again, or until the garage door opener is activated.

Once the garage door opener is activated the lights will turn offafter the specified period oftime (the

factorysetting is 4-1/2 minutes). The LIGHTbutton will not control the lights when the door is in motion.

The duration of the lighttiming can be adjusted by accessing the menu using the navigation buttons.

SCREEN

The screen will display the time and temperature until the menu button is pressed, and then it will

display the menu options.Ifthere is a problem with the garage door opener the screen will display the

Diagnostic Code. Refer to the Troubleshooting section.

The following features are accessible through the screen using the navigation buttons:

LEARN A DEVICE

Any compatible remote controls, wireless keylessentry,or MyQ

accessoriescan be programmed to

the garage door opener byaccessing the menu and using the navigation buttons.

LOCK

The LOCK feature is designed to preventactivation of the garage door opener from remote controls

while still allowing activation fromthe door control and keyless entry. This feature is useful for added

peace ofmind when the home is empty (i.e. vacation).

TIMER-TO-CLOSE (TTC)

DO NOTenable TTC ifoperating a one-piece door. TTC is to be used ONLY with sectional doors.

Factory defaultis set to off. TTCcan be setto automatically close your garage door from the fully open

position after a specified period of time (1, 5,10 minute intervals). The garage door opener will Beep

and the lights will Flash before closing the door. The screen on the door control can display the status of

the TTC. TTC WILL NOT work ifthe garage door opener is operating by battery power or if the safety

reversing sensors are misaligned.This feature is NOT intended to be the primary method ofclosing the

door.A keyless entry should be installed inthe event of an accidentallock out when usingthis

feature.

NOTE: Before enabling the TTC for the first time, or if you experience a power outage, cycle the garage

door opener open and closed to allow the TTC to set.

AUTOMATIC LIGHT

Motion Sensor

Factory defaultis set to on.This feature automatically turns on the garage door opener lightswhen

motion is sensed. The lights will come on for the setperiod of time,then shut off. If using the garage door

opener light as a work light disable the motion sensor,otherwise the lightwill turn offautomatically ifyou

are beyond the range ofthe sensor.

Light Feature

The lights will turn on when someone entersthrough the open garage door and the safetyreversing

sensor infrared beam isbroken.

MAINTENANCE ALERT (MAS)

This feature assiststhe homeowner in ensuring the garage door opener system staysin good working

condition. A maintenance alertmessage will display on the screen indicating the garage door opener

maybe in need of maintenance. The factory setting for the MASfeature is off and can be activated at

time of installation. Contact your installing dealer for service.

Door Control

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 81 82

Comentarios a estos manuales

Sin comentarios

Controlled-products-systems-group 8550C-7 Manual de usuario Pagina 30

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Controlled-products-systems-group 8550C-7