Controlled-products-systems-group SLIDESMART DC 10F Manual de usuario Pagina 77
- Pagina / 148
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installer Menu
Revision D Display and Menu Options 3-25
12
0 = maximum sensitivity
2 = moderate sensitivity
9 = least sensitivity
Adjusts the sensitivity of the internal inherent entrapment
sensor (IES). Available settings are 0 to 9 with 9 being the
least sensitive. HySecurity strongly recommends that you
avoid setting the IES sensitivity higher than 6.
Note: Before changing the IES sensitivity, make sure that
the gate rolls smoothly without obstruction. Fix any
issues with gate hardware.
See Note.
13
0 = stop, reverse for 2s
1 = stop only
In a Usage Class 4 environment, the operator can be set to
stop the gate and not reverse gate travel after an IES trip.
Note: This menu option only appears when the Usage
Class is set to 4.
(N/A)
14
0 = no delay
1 through 20 in ½ second
increments
For example:
1 = ½ second
10 = 5 seconds
20 = 10 seconds
Only appears if the gate operator is set up as a Master or a
Slave. Available settings are 1 through 20. Each increment
adds ½ second time delay following a command to close
before the operator activates. Provides up to a 10 second
time delay.
DUAL GATE inputs on
both operators
15
0 = no delay
1 through 20 in ½ second
increments
For example:
1 = ½ second
10 = 5 seconds
20 = 10 seconds
Only appears if the gate operator is set up as a Master or a
Slave. Available settings are 1 through 20. Each increment
adds ½ second time delay following a command to open
before the operator activates. Provides up to a 10 second
time delay.
DUAL GATE inputs on
both operators
Table 3-2. Smart DC Controller - Installer Menu Functions (Continued)
Ref.
No.
*
Installer Menu
Setting Options
(
Bold = Factory Settings
) Tasks and Explanations
Associated
DC Controller
Connections
Display
SE 2
IES SENSITIVITY
SS 0 (OFF)
IES STOP ONLY
LC 0 (0.0 SECS)
LEAF DELAY CLOSE
LO 0 (0.0 SECS)
LEAF DELAY OPEN
- SlideSmart DC 1
- OMPONENTS 4
- Contents 5
- Introducing SlideSmart DC 9
- ECHNICAL 10
- NSTALLER 11
- Installer's Check List 12
- Safety Requirements 13
- ECONDARY 17
- NTRAPMENT 17
- ROTECTION 17
- Class I 18
- Class II 18
- Class III 18
- Class IV 18
- Class IV A B1, B2, C, D, or E 19
- MERGENCY 20
- & S 21
- NDUSTRIAL 22
- Installation 23
- Pad Condition 24
- Using an Existing Pad 25
- Front Installation 26
- Rear Installation 27
- NPACKING 28
- PUBLICPUBLIC 29
- SECURESECURE 29
- NSTALLATION 30
- Aligning the Chain 31
- Connect red battery wire 32
- Turn DC power ON 32
- WT 0 33
- GATE WEIGHT (LB) 33
- HYSECURITY 34
- GATE CLOSED 34
- Installing the Target Magnet 35
- Chapter 2 39
- Service Outlet 41
- 115VAC, 15A 41
- Wiring 115VAC Power 42
- Wiring 208/230VAC Power 42
- Voltage selector switch 43
- Map Legend 48
- MPORTANT 49
- ONSIDERATIONS 49
- PERATORS 49
- 50Ah batteries 51
- Accessory tray 51
- Post-mounted 51
- Display and Menu Options 53
- CT 0 (OFF) 55
- CLOSE TIMER 55
- Setting the Time and Date 61
- AP 0 (AC LOSS) 62
- UPS FAIL OPEN 62
- LD 5 63
- LCD CONTRAST 63
- User Menu 64
- DS 0 (OFF) 66
- DIAGNOSTIC LOGS 66
- Adjusting Gate Speed 69
- Adjusting the IES Sensitivity 70
- LL 0 (OFF) 71
- LEARN LIMIT 71
- Reinstating Factory Defaults 72
- Smart DC Controller 83
- Terminal 85
- Input Name Use 85
- HY-5A V 87
- (Bold - Default) 88
- Display Meaning 88
- Entrapment Sensor Connections 91
- Manual Push Button Station 92
- No. Name Description 93
- Bi-parting Gate Systems 95
- Slave Master 96
- Master Slave 96
- LL 0 (OFF) 97
- Master and Slave Menu Setup 98
- Reference 99
- USER 1 RELAY 101
- Installing a Lock for 102
- High Voltage 102
- Installer Menu 103
- NSTALLING 104
- ETECTORS 104
- Figure 6-7 106
- PERATION 107
- Other options include: 108
- UPERVISED 109
- ONNECTION 109
- Revision D Reference 6-13 111
- Two Channel Radio Receiver 113
- ONTROLLER 114
- ROUBLESHOOTING 114
- Display Description 115
- Possible Causes Solutions 115
- Alert or Error 121
- Installer 122
- Menu LCD Description 122
- Setting Options 122
- Bold = Factory Settings 122
- SlideSmart Schematics 123
- Figure 6-15 124
- AINTENANCE 125
- Electrical Controls 126
- Mechanical Maintenance 127
- Software Maintenance 127
- 1/16" to 1/8" 128
- EPLACEMENT 129
- General Maintenance 132
- Installation Configurations 133
- SLIDESMART INSTALLATION 134
- SPECIFICATION 134
- Parts & Limited Warranty 145
- G-2 Revision D 146
- April 2010, D0317 147
- PECIFICATIONS 148
Relacionado con productos y manuales para La Seguridad Controlled-products-systems-group SLIDESMART DC 10F
(36 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales