Controlled-products-systems-group SLIDESMART DC 10F Manual de usuario Pagina 79
- Pagina / 148
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installer Menu
Revision D Display and Menu Options 3-27
21
0 = IES reverses full open
1 = 2 second reversal only
The default setting is a two-second duration reversal if the
inherent sensor is triggered. The optional setting of 0 will
cause the gate to reopen fully if triggered while closing.
N/A
22
0 = Normally Open PE output
1 = Normally Closed
(supervised)
The default setting is photo eyes with Normally Open
outputs. The optional setting 1 requires a Normally Closed
(NC) output which requires that both a photo EYE OPEN
and a photo EYE CLOSE are connected. If set for NC, the
connection is also supervised and any open or short circuit
fault will generate a FAULT 2 alert which requires a STOP
button reset to re-enable any function if triggered.
Photo eye connections:
EYE OPEN
EYE CLOSE
EYE COM
+24V
23
0 = Normally Open Edge
1 = Normally Closed
The default setting is edge sensor with Normally Open
(NO) output. The optional setting of 1 requires an (NC)
output.
EDGE
COM
24
0 = Disable Free Exit
1 = Disable Close Timer
Configures the BLOCK EXIT input to disable either the
Free Exit Detector function or, alternately, the Timer To
Close function. The default setting disables the free exit
detector.
Note: The free exit is disabled when the gate is at its closed
limit. If the closed limit is not tripped, the free exit
continues to work normally.
BLOCK EXIT
COM
Table 3-2. Smart DC Controller - Installer Menu Functions (Continued)
Ref.
No.
*
Installer Menu
Setting Options
(
Bold = Factory Settings
) Tasks and Explanations
Associated
DC Controller
Connections
Display
SR 1 REVERSE 2S
IES SENSOR LOGIC
PC 0 NO CONTACT
PHOTO EYE OUTPUT
GC 0 NO CONTACT
GATE EDGE OUTPUT
DT 0 FREE EXIT
DISABLE FUNCTION
- SlideSmart DC 1
- OMPONENTS 4
- Contents 5
- Introducing SlideSmart DC 9
- ECHNICAL 10
- NSTALLER 11
- Installer's Check List 12
- Safety Requirements 13
- ECONDARY 17
- NTRAPMENT 17
- ROTECTION 17
- Class I 18
- Class II 18
- Class III 18
- Class IV 18
- Class IV A B1, B2, C, D, or E 19
- MERGENCY 20
- & S 21
- NDUSTRIAL 22
- Installation 23
- Pad Condition 24
- Using an Existing Pad 25
- Front Installation 26
- Rear Installation 27
- NPACKING 28
- PUBLICPUBLIC 29
- SECURESECURE 29
- NSTALLATION 30
- Aligning the Chain 31
- Connect red battery wire 32
- Turn DC power ON 32
- WT 0 33
- GATE WEIGHT (LB) 33
- HYSECURITY 34
- GATE CLOSED 34
- Installing the Target Magnet 35
- Chapter 2 39
- Service Outlet 41
- 115VAC, 15A 41
- Wiring 115VAC Power 42
- Wiring 208/230VAC Power 42
- Voltage selector switch 43
- Map Legend 48
- MPORTANT 49
- ONSIDERATIONS 49
- PERATORS 49
- 50Ah batteries 51
- Accessory tray 51
- Post-mounted 51
- Display and Menu Options 53
- CT 0 (OFF) 55
- CLOSE TIMER 55
- Setting the Time and Date 61
- AP 0 (AC LOSS) 62
- UPS FAIL OPEN 62
- LD 5 63
- LCD CONTRAST 63
- User Menu 64
- DS 0 (OFF) 66
- DIAGNOSTIC LOGS 66
- Adjusting Gate Speed 69
- Adjusting the IES Sensitivity 70
- LL 0 (OFF) 71
- LEARN LIMIT 71
- Reinstating Factory Defaults 72
- Smart DC Controller 83
- Terminal 85
- Input Name Use 85
- HY-5A V 87
- (Bold - Default) 88
- Display Meaning 88
- Entrapment Sensor Connections 91
- Manual Push Button Station 92
- No. Name Description 93
- Bi-parting Gate Systems 95
- Slave Master 96
- Master Slave 96
- LL 0 (OFF) 97
- Master and Slave Menu Setup 98
- Reference 99
- USER 1 RELAY 101
- Installing a Lock for 102
- High Voltage 102
- Installer Menu 103
- NSTALLING 104
- ETECTORS 104
- Figure 6-7 106
- PERATION 107
- Other options include: 108
- UPERVISED 109
- ONNECTION 109
- Revision D Reference 6-13 111
- Two Channel Radio Receiver 113
- ONTROLLER 114
- ROUBLESHOOTING 114
- Display Description 115
- Possible Causes Solutions 115
- Alert or Error 121
- Installer 122
- Menu LCD Description 122
- Setting Options 122
- Bold = Factory Settings 122
- SlideSmart Schematics 123
- Figure 6-15 124
- AINTENANCE 125
- Electrical Controls 126
- Mechanical Maintenance 127
- Software Maintenance 127
- 1/16" to 1/8" 128
- EPLACEMENT 129
- General Maintenance 132
- Installation Configurations 133
- SLIDESMART INSTALLATION 134
- SPECIFICATION 134
- Parts & Limited Warranty 145
- G-2 Revision D 146
- April 2010, D0317 147
- PECIFICATIONS 148
Relacionado con productos y manuales para La Seguridad Controlled-products-systems-group SLIDESMART DC 10F
(36 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales