Controlled-products-systems-group SLIDESMART DC 10F Manual de usuario Pagina 78
- Pagina / 148
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installer Menu
3-26 SlideSmart DC Installation and Reference Manual Revision D
16
0 = 80 Seconds max run,
1 = 300 Seconds max run
Assigns a motor run time of 80 or 300 seconds. If the gate
opening or closure takes longer than 80 seconds, you’ll need
to set the run timer to 1.
(N/A)
17
0 = OFF
7 = 7 ft, 8 = 8ft, through
32 = 32 ft
Sets the distance (from the closed gate position) where the
gate stops in a partial open.When a number is entered in
the PO display, the open partial input becomes operational.
OPEN PARTIAL
COM
18
0 = Close eye stops only
1 = 2s reverse to open
The default setting is non-reversal if the close photo eye is
triggered. A setting of 1 causes the gate to reverse and travel
open for two seconds if triggered while closing.
EYE CLOSE
EYE COM
19
0 = Open eye stops only
1 = 2s reverse to close
The default setting is non-reversal if the open photo eye is
triggered. A setting of 1 causes the gate to reverse travel and
close for two seconds if triggered while opening.
EYE OPEN
EYE COM
20
0 = Edge reverses full open
1 = 2s reversal only
The default setting is a full-open reversal if the gate edge is
triggered while closing. The optional setting of 1 causes the
gate to reverse for two seconds if triggered while closing.
EDGE
COM
Table 3-2. Smart DC Controller - Installer Menu Functions (Continued)
Ref.
No.
*
Installer Menu
Setting Options
(
Bold = Factory Settings
) Tasks and Explanations
Associated
DC Controller
Connections
Display
RT 0 (80 SECS)
MAXIMUM RUN TIMER
PO 0 (OFF)
PARTIAL OPEN
EC 0 (STOP ONLY)
EYE CLOSE LOGIC
EO 0 (STOP ONLY)
EYE OPEN LOGIC
GR 0 (FULL OPEN)
GATE EDGE LOGIC
- SlideSmart DC 1
- OMPONENTS 4
- Contents 5
- Introducing SlideSmart DC 9
- ECHNICAL 10
- NSTALLER 11
- Installer's Check List 12
- Safety Requirements 13
- ECONDARY 17
- NTRAPMENT 17
- ROTECTION 17
- Class I 18
- Class II 18
- Class III 18
- Class IV 18
- Class IV A B1, B2, C, D, or E 19
- MERGENCY 20
- & S 21
- NDUSTRIAL 22
- Installation 23
- Pad Condition 24
- Using an Existing Pad 25
- Front Installation 26
- Rear Installation 27
- NPACKING 28
- PUBLICPUBLIC 29
- SECURESECURE 29
- NSTALLATION 30
- Aligning the Chain 31
- Connect red battery wire 32
- Turn DC power ON 32
- WT 0 33
- GATE WEIGHT (LB) 33
- HYSECURITY 34
- GATE CLOSED 34
- Installing the Target Magnet 35
- Chapter 2 39
- Service Outlet 41
- 115VAC, 15A 41
- Wiring 115VAC Power 42
- Wiring 208/230VAC Power 42
- Voltage selector switch 43
- Map Legend 48
- MPORTANT 49
- ONSIDERATIONS 49
- PERATORS 49
- 50Ah batteries 51
- Accessory tray 51
- Post-mounted 51
- Display and Menu Options 53
- CT 0 (OFF) 55
- CLOSE TIMER 55
- Setting the Time and Date 61
- AP 0 (AC LOSS) 62
- UPS FAIL OPEN 62
- LD 5 63
- LCD CONTRAST 63
- User Menu 64
- DS 0 (OFF) 66
- DIAGNOSTIC LOGS 66
- Adjusting Gate Speed 69
- Adjusting the IES Sensitivity 70
- LL 0 (OFF) 71
- LEARN LIMIT 71
- Reinstating Factory Defaults 72
- Smart DC Controller 83
- Terminal 85
- Input Name Use 85
- HY-5A V 87
- (Bold - Default) 88
- Display Meaning 88
- Entrapment Sensor Connections 91
- Manual Push Button Station 92
- No. Name Description 93
- Bi-parting Gate Systems 95
- Slave Master 96
- Master Slave 96
- LL 0 (OFF) 97
- Master and Slave Menu Setup 98
- Reference 99
- USER 1 RELAY 101
- Installing a Lock for 102
- High Voltage 102
- Installer Menu 103
- NSTALLING 104
- ETECTORS 104
- Figure 6-7 106
- PERATION 107
- Other options include: 108
- UPERVISED 109
- ONNECTION 109
- Revision D Reference 6-13 111
- Two Channel Radio Receiver 113
- ONTROLLER 114
- ROUBLESHOOTING 114
- Display Description 115
- Possible Causes Solutions 115
- Alert or Error 121
- Installer 122
- Menu LCD Description 122
- Setting Options 122
- Bold = Factory Settings 122
- SlideSmart Schematics 123
- Figure 6-15 124
- AINTENANCE 125
- Electrical Controls 126
- Mechanical Maintenance 127
- Software Maintenance 127
- 1/16" to 1/8" 128
- EPLACEMENT 129
- General Maintenance 132
- Installation Configurations 133
- SLIDESMART INSTALLATION 134
- SPECIFICATION 134
- Parts & Limited Warranty 145
- G-2 Revision D 146
- April 2010, D0317 147
- PECIFICATIONS 148
Relacionado con productos y manuales para La Seguridad Controlled-products-systems-group SLIDESMART DC 10F
(36 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales